esphome:
  name: ventilation-bath
  friendly_name: Ventilation-bath

esp32:
  board: esp32dev
  framework:
    type: arduino

# Enable logging
logger:

# Enable Home Assistant API
api:
  encryption:
    key: "lchXaoHfpB83F50n78hQX2+whi5p0V5TpTCdbegE/Sg="

ota:
  - platform: esphome
    password: "539b8a397419f5db2ba6f6e3192eca2f"

wifi:
  ssid: 'SmartHome'
  password: ''
  use_address: 192.168.88.29

  manual_ip:
    static_ip: 192.168.88.29
    gateway: 192.168.88.1
    subnet: 255.255.255.0

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  # ap:
  #   ssid: "Kc868-A6 Fallback Hotspot"
  #   password: "Eqh4eO1YIQUi"

uart:
    #RS485
  - id: uart_modbus
    tx_pin: GPIO27
    rx_pin: GPIO14
    baud_rate: 9600
    # stop_bits: 1


    #RS2332
  - id: rs232
    tx_pin: GPIO17
    rx_pin: GPIO16
    baud_rate: 9600

spi:
  clk_pin: GPIO18
  mosi_pin: GPIO23
  miso_pin: GPIO19
  # cs pin: GPIO5

# modbus:
#   uart_id: uart_modbus
#   id: modbus1

# modbus_controller:
#   - id: modbus_sensor
#     address: 0x01  # device address
#     modbus_id: modbus1
#     update_interval: 2s

i2c:
  sda: GPIO4
  scl:
    number: GPIO15
    ignore_strapping_warning: true

pcf8574:
  - id: inputs
    address: 0x22
  - id: outputs
    address: 0x24

time:
  - platform: ds1307
    id: rtc_time


binary_sensor:
  - platform: gpio
    name: "KC868-A6-IN-1"
    pin:
      pcf8574: inputs
      number: 0
      mode: INPUT
      inverted: true
    on_press:
      - switch.toggle: switch_output1
    on_release: 
      - switch.toggle: switch_output1

  - platform: gpio
    name: "KC868-A6-IN-2"
    pin:
      pcf8574: inputs
      number: 1
      mode: INPUT
      inverted: true
    on_press:
      - switch.toggle: switch_output2
    on_release: 
      - switch.toggle: switch_output2

  - platform: gpio
    name: "KC868-A6-IN-3"
    pin:
      pcf8574: inputs
      number: 2
      mode: INPUT
      inverted: true
    on_press:
      - switch.toggle: switch_output3
    on_release: 
      - switch.toggle: switch_output3

  - platform: gpio
    name: "KC868-A6-IN-4"
    pin:
      pcf8574: inputs
      number: 3
      mode: INPUT
      inverted: true
    on_press:
      - switch.toggle: switch_output4
    on_release: 
      - switch.toggle: switch_output4

  - platform: gpio
    name: "KC868-A6-IN-5"
    pin:
      pcf8574: inputs
      number: 4
      mode: INPUT
      inverted: true
    on_press:
      - switch.toggle: switch_output5
    on_release: 
      - switch.toggle: switch_output5

  - platform: gpio
    name: "KC868-A6-IN-6"
    pin:
      pcf8574: inputs
      number: 5
      mode: INPUT
      inverted: true
    on_press:
      - switch.toggle: switch_output6
    on_release: 
      - switch.toggle: switch_output6

switch:
  - platform: gpio
    name: "KC868-A6-RELAY-1"
    id: switch_output1
    pin:
      pcf8574: outputs
      number: 0
      mode: OUTPUT
      inverted: true

  - platform: gpio
    name: "KC868-A6-RELAY-2"
    id: switch_output2
    pin:
      pcf8574: outputs
      number: 1
      mode: OUTPUT
      inverted: true

  - platform: gpio
    name: "KC868-A6-RELAY-3"
    id: switch_output3
    pin:
      pcf8574: outputs
      number: 2
      mode: OUTPUT
      inverted: true

  - platform: gpio
    name: "KC868-A6-RELAY-4"
    id: switch_output4
    pin:
      pcf8574: outputs
      number: 3
      mode: OUTPUT
      inverted: true

  - platform: gpio
    name: "KC868-A6-RELAY-5"
    id: switch_output5
    pin:
      pcf8574: outputs
      number: 4
      mode: OUTPUT
      inverted: true

  - platform: gpio
    name: "KC868-A6-RELAY-6"
    id: switch_output6
    pin:
      pcf8574: outputs
      number: 5
      mode: OUTPUT
      inverted: true

sensor:
  # - platform: modbus_controller
  #   modbus_controller_id: modbus_sensor
  #   name: "Temperature SHT30"
  #   id: temperature_sensor
  #   address: 0x0001
  #   register_type: read
  #   value_type: U_WORD
  #   unit_of_measurement: "°C"
  #   accuracy_decimals: 1
  #   filters:
  #     - lambda: if (x < 10000) return x * 0.1; else return -1 * (x - 10000) * 0.1;
    
  # - platform: modbus_controller
  #   modbus_controller_id: modbus_sensor
  #   name: "Humidity_SHT30"
  #   id: humidity_sensor
  #   address: 0x0002
  #   register_type: read
  #   value_type: U_WORD
  #   unit_of_measurement: "%"
  #   accuracy_decimals: 1
  #   filters:
  #     - multiply: 0.1

    

web_server:
  port: 80
  auth:
    username: "silver"
    password: "cbvgcjy0"

mqtt:
  broker: 192.168.88.4
  username: 'miroca'
  password: 'cbvgcjy0'
  discovery: False # disable entity discovery
  discover_ip: True # enable device discovery