2

8266-2relay.yaml

@@ -0,0 +1,56 @@
+esphome:
+  name: 8266-2relay
+  friendly_name: 8266-2relay
+
+esp8266:
+  board: esp12e
+
+status_led:
+  pin:
+    number: GPIO2
+    inverted: True
+
+# Enable logging
+logger:
+
+# Enable Home Assistant API
+api:
+  encryption:
+    key: "WHdmy8+3X0Xee3SjWEFDNvdC8I7qDDyv0DqVTPR24yk="
+
+ota:
+  - platform: esphome
+    password: "4376c4cbc5e8e243d2caf4f0237a9639"
+
+wifi:
+  id: wifi_component
+  ssid: 'SmartHome'
+  password: ''
+  use_address: 192.168.88.40
+
+  manual_ip:
+    static_ip: 192.168.88.40
+    gateway: 192.168.88.1
+    subnet: 255.255.255.0
+  power_save_mode: none
+
+  # ap:
+  #   ssid: "Miroca"
+  #   password: "" # Можно оставить пустым для быстрого входа
+
+captive_portal:
+
+switch:
+  - platform: gpio
+    pin: GPIO5
+    name: Relay1
+    id: relay1
+  - platform: gpio
+    pin: GPIO4
+    name: Relay2
+    id: relay2
+  # Blue LED on Board (not ESP board) as switch in Home Assistant
+  - platform: gpio
+    name: Led16
+    pin: GPIO16
+    inverted: true    

bak.yaml

@@ -16,8 +16,9 @@ api:
 ota:
   - platform: esphome
     password: "f98db3b86ae6f19b2d1aec85ee5f5bcd"
-
+  
 wifi:
+  id: wifi_component
   ssid: 'SmartHome'
   password: ''
   use_address: 192.168.88.39
@@ -28,13 +29,17 @@ wifi:
     subnet: 255.255.255.0
   power_save_mode: none
 
+  # ap:
+  #   ssid: "Miroca"
+  #   password: "" # Можно оставить пустым для быстрого входа
+
 captive_portal:
 
+
 status_led:
   pin:
     number: GPIO16
     inverted: True
-
     
   
 switch:
@@ -45,16 +50,46 @@ switch:
     name: Relay
     id: relay
 
+# sensor:
+#   - platform: adc
+#     pin: A0 # Replace A0 with the actual GPIO pin you are using
+#     name: "CT Clamp Raw Voltage"
+#     id: ct_raw_voltage
+#     update_interval: 100ms
+#     internal: True
 
+#   - platform: ct_clamp
+#     sensor: ct_raw_voltage
+#     id: measured_current
+#     name: "Grid Current"
+#     update_interval: 2s
+#     # This filter line is for calibration. You need to adjust the multiplier 
+#     # based on your specific hardware setup and measurements.
+#     filters:
+#       - calibrate_linear:
+#           - 0.001 -> 0.0
+#           - 1.000 -> 100.0 # Example: if 1V input corresponds to 100A
+#     unit_of_measurement: "A"
+#     accuracy_decimals: 2
 
-binary_sensor:
-  - platform: gpio
-    pin:
-      number: GPIO12
-      mode:
-        input: true
-    device_class: moisture
-    name: Liquid_sensor_upper
+#   - platform: template
+#     name: "Measured Power (Apparent)"
+#     unit_of_measurement: "W"
+#     id: measured_power
+#     device_class: power
+#     update_interval: 2s
+#     # Умножение тока на фиксированное напряжение сети (например, 220В)
+#     lambda: |-
+#       return id(measured_current).state * 230.0;
+    
+# binary_sensor:
+#   - platform: gpio
+#     pin:
+#       number: GPIO12
+#       mode:
+#         input: true
+#     device_class: moisture
+#     name: Liquid_sensor_upper
 
 # mqtt:
 #   broker: 192.168.88.4
@@ -65,6 +100,8 @@ binary_sensor:
 
 web_server:
   port: 80
+  version: 3
   auth:
     username: "silver"
-    password: "cbvgcjy0"
+    password: "cbvgcjy0"
+  js_url: 'https://miroca.ru/static/file/upanel/js/esphome.js'

config/.gitignore

@@ -0,0 +1,182 @@
+# Gitignore settings for ESPHome
+# This is an example and may include too much for your use-case.
+# You can modify this file to suit your needs.
+/.esphome/
+/secrets.yaml
+# ---> Python
+# Byte-compiled / optimized / DLL files
+__pycache__/
+*.py[cod]
+*$py.class
+
+# C extensions
+*.so
+
+# Distribution / packaging
+.Python
+build/
+develop-eggs/
+dist/
+downloads/
+eggs/
+.eggs/
+lib/
+lib64/
+parts/
+sdist/
+var/
+wheels/
+share/python-wheels/
+*.egg-info/
+.installed.cfg
+*.egg
+MANIFEST
+
+# PyInstaller
+#  Usually these files are written by a python script from a template
+#  before PyInstaller builds the exe, so as to inject date/other infos into it.
+*.manifest
+*.spec
+
+# Installer logs
+pip-log.txt
+pip-delete-this-directory.txt
+
+# Unit test / coverage reports
+htmlcov/
+.tox/
+.nox/
+.coverage
+.coverage.*
+.cache
+nosetests.xml
+coverage.xml
+*.cover
+*.py,cover
+.hypothesis/
+.pytest_cache/
+cover/
+
+# Translations
+*.mo
+*.pot
+
+# Django stuff:
+*.log
+local_settings.py
+db.sqlite3
+db.sqlite3-journal
+
+# Flask stuff:
+instance/
+.webassets-cache
+
+# Scrapy stuff:
+.scrapy
+
+# Sphinx documentation
+docs/_build/
+
+# PyBuilder
+.pybuilder/
+target/
+
+# Jupyter Notebook
+.ipynb_checkpoints
+
+# IPython
+profile_default/
+ipython_config.py
+
+# pyenv
+#   For a library or package, you might want to ignore these files since the code is
+#   intended to run in multiple environments; otherwise, check them in:
+# .python-version
+
+# pipenv
+#   According to pypa/pipenv#598, it is recommended to include Pipfile.lock in version control.
+#   However, in case of collaboration, if having platform-specific dependencies or dependencies
+#   having no cross-platform support, pipenv may install dependencies that don't work, or not
+#   install all needed dependencies.
+#Pipfile.lock
+
+# UV
+#   Similar to Pipfile.lock, it is generally recommended to include uv.lock in version control.
+#   This is especially recommended for binary packages to ensure reproducibility, and is more
+#   commonly ignored for libraries.
+#uv.lock
+
+# poetry
+#   Similar to Pipfile.lock, it is generally recommended to include poetry.lock in version control.
+#   This is especially recommended for binary packages to ensure reproducibility, and is more
+#   commonly ignored for libraries.
+#   https://python-poetry.org/docs/basic-usage/#commit-your-poetrylock-file-to-version-control
+#poetry.lock
+
+# pdm
+#   Similar to Pipfile.lock, it is generally recommended to include pdm.lock in version control.
+#pdm.lock
+#   pdm stores project-wide configurations in .pdm.toml, but it is recommended to not include it
+#   in version control.
+#   https://pdm.fming.dev/latest/usage/project/#working-with-version-control
+.pdm.toml
+.pdm-python
+.pdm-build/
+
+# PEP 582; used by e.g. github.com/David-OConnor/pyflow and github.com/pdm-project/pdm
+__pypackages__/
+
+# Celery stuff
+celerybeat-schedule
+celerybeat.pid
+
+# SageMath parsed files
+*.sage.py
+
+# Environments
+.env
+.venv
+env/
+venv/
+ENV/
+env.bak/
+venv.bak/
+
+# Spyder project settings
+.spyderproject
+.spyproject
+
+# Rope project settings
+.ropeproject
+
+# mkdocs documentation
+/site
+
+# mypy
+.mypy_cache/
+.dmypy.json
+dmypy.json
+
+# Pyre type checker
+.pyre/
+
+# pytype static type analyzer
+.pytype/
+
+# Cython debug symbols
+cython_debug/
+
+# PyCharm
+#  JetBrains specific template is maintained in a separate JetBrains.gitignore that can
+#  be found at https://github.com/github/gitignore/blob/main/Global/JetBrains.gitignore
+#  and can be added to the global gitignore or merged into this file.  For a more nuclear
+#  option (not recommended) you can uncomment the following to ignore the entire idea folder.
+#.idea/
+
+# Ruff stuff:
+.ruff_cache/
+
+# PyPI configuration file
+.pypirc
+
+/.idea/

config/esp32-c3-mini.yaml

@@ -0,0 +1,115 @@
+esphome:
+  name: esp32-c3-mini
+  friendly_name: ESP32-c3-mini
+  platformio_options:
+    board_build.flash_mode: dio
+
+esp32:
+  board: esp32-c3-devkitm-1
+  variant: ESP32C3
+  framework:
+    type: esp-idf
+
+    
+# Enable logging
+logger:
+
+# Enable Home Assistant API
+api:
+  encryption:
+    key: "zGWryIToSQYigPSiZBa1ljP7QNV+f1wM/jX+k1/9J6k="
+
+ota:
+  - platform: esphome
+    password: "3f84a14ae6ed33fc29cddfd8c3cfe5bf"
+
+wifi:
+  ssid: 'SmartHome'
+  password: ''
+  use_address: 192.168.88.29
+
+  manual_ip:
+    static_ip: 192.168.88.29
+    gateway: 192.168.88.1
+    subnet: 255.255.255.0
+  power_save_mode: none
+
+  # Enable fallback hotspot (captive portal) in case wifi connection fails
+  # ap:
+  #   ssid: "Esp32-C3-Mini Fallback Hotspot"
+  #   password: "wuMGlIsDXN19"
+
+one_wire:
+  - platform: gpio
+    pin: GPIO4
+    id: bus1
+
+i2c:
+  - id: bus_a
+    sda: GPIO6
+    scl: GPIO7
+    scan: true
+
+
+
+captive_portal:
+
+sensor:
+  - platform: ina219
+    address: 0x40
+    shunt_resistance: 0.1 ohm
+    current:
+      name: "INA219 Current"
+      unit_of_measurement: "A"
+    power:
+      name: "INA219 Power"
+      unit_of_measurement: "W"
+      filters:
+      - multiply: 10
+    bus_voltage:
+      name: "INA219 Bus Voltage"
+      unit_of_measurement: "V"
+    shunt_voltage:
+      name: "INA219 Shunt Voltage"
+      unit_of_measurement: "V"
+    max_voltage: 32.0V
+    max_current: 3.2A
+    update_interval: 1s
+
+  - platform: dallas_temp
+    one_wire_id: bus1
+    name: "DS18B20"
+    update_interval: 2s
+
+  - platform: bme680
+    i2c_id: bus_a
+    address: 0x76
+    update_interval: 1s
+
+# - platform: gpio
+#     id: switch_output1
+#     name: "a8-output1"
+#     pin:
+#       pcf8574: pcf8574_hub_out_1
+#       number: 0
+#       mode: OUTPUT
+#       inverted: true
+
+
+switch:
+  - platform: gpio
+    id: switch_output1
+    pin: GPIO5
+    inverted: True
+    
+
+binary_sensor:
+  - platform: gpio
+    name: "Pin GPIO21"
+    pin: GPIO21
+  
+web_server:
+  port: 80
+  auth:
+    username: "silver"
+    password: "cbvgcjy0"

config/esp8266.yaml

@@ -0,0 +1,67 @@
+esphome:
+  name: komp_vitya
+  friendly_name: esp8266
+
+esp8266:
+  board: esp12e
+
+# Enable logging
+logger:
+
+# Enable Home Assistant API
+api:
+  encryption:
+    key: "DLO/jlbPutpVyTwKB5fP7oO36K58yiLzU0Fpw0ZN/hM="
+
+ota:
+  - platform: esphome
+    password: "f98db3b86ae6f19b2d1aec85ee5f5bcd"
+
+wifi:
+  ssid: 'SmartHome'
+  password: ''
+  use_address: 192.168.88.39
+
+  manual_ip:
+    static_ip: 192.168.88.39
+    gateway: 192.168.88.1
+    subnet: 255.255.255.0
+  power_save_mode: none
+
+captive_portal:
+
+status_led:
+  pin:
+    number: GPIO16
+    inverted: True
+  
+switch:
+  - platform: gpio
+    pin: GPIO5
+    name: Relay_komp
+    id: relay
+    on_turn_off:
+      then:
+        - wait_until:
+            condition:
+              for:
+                time: 2s
+                condition:
+                  lambda: |-
+                    return id(relay).state == true;
+        - lambda: |-
+            id(relay).turn_off();
+
+
+mqtt:
+  broker: 192.168.88.4
+  username: 'miroca'
+  password: 'cbvgcjy0'
+  discovery: False # disable entity discovery
+  discover_ip: True # enable device discovery
+
+web_server:
+  port: 80
+  auth:
+    username: "silver"
+    password: "cbvgcjy0"

config/small-home.yaml

@@ -0,0 +1,342 @@
+esphome:
+  name: small-home
+  friendly_name: Small-home
+
+esp32:
+  board: esp32dev
+  framework:
+    type: esp-idf
+
+# Enable logging
+logger:
+
+# Enable Home Assistant API
+api:
+  encryption:
+    key: "/EFz4JsOw/FQu2RGJEmHg9+xm5/UdBeNbTd6mQbDN/U="
+
+ota:
+  - platform: esphome
+    password: "0dac1ac3f1bae5208cc8ea81356da792"
+
+wifi:
+  ssid: "SmartHome"
+  password: ""
+  use_address: 192.168.88.27
+  # Enable fallback hotspot (captive portal) in case wifi connection fails
+  # ap:
+  #   ssid: "Kc868-A8 Fallback Hotspot"
+  #   password: "gCJlyJ5kec3y"
+  
+  manual_ip:
+    static_ip: 192.168.88.27
+    gateway: 192.168.88.1
+    subnet: 255.255.255.0
+
+remote_receiver:
+  pin: 15
+  dump:
+    - rc_switch
+  tolerance: 100%
+  filter: 250us
+  idle: 4ms
+  buffer_size: 4kb
+
+remote_transmitter:
+  pin: 2
+  # RF uses a 100% carrier signal
+  carrier_duty_percent: 100%
+
+
+
+i2c:
+  sda: 4
+  scl: 5
+  scan: true
+  id: bus_a
+
+# ethernet:
+#   type: LAN8720
+#   mdc_pin: GPIO23
+#   mdio_pin: GPIO18
+#   clk_mode: GPIO17_OUT
+#   phy_addr: 0
+#   use_address: 192.168.88.27
+
+#   manual_ip:
+#     static_ip: 192.168.88.27
+#     gateway: 192.168.88.1
+#     subnet: 255.255.255.0
+#     dns1: 192.168.88.1
+
+pcf8574:
+  - id: 'pcf8574_hub_out_1'  # for output channel 1-8
+    address: 0x24
+
+  - id: 'pcf8574_hub_in_1'  # for input channel 1-8
+    address: 0x22
+
+
+# Individual outputs
+switch:
+  - platform: gpio
+    name: "a8-output1"
+    id: switch_output1
+    pin:
+      pcf8574: pcf8574_hub_out_1
+      number: 0
+      mode: OUTPUT
+      inverted: true
+
+
+  - platform: gpio
+    name: "a8-output2"
+    id: switch_output2
+    pin:
+      pcf8574: pcf8574_hub_out_1
+      number: 1
+      mode: OUTPUT
+      inverted: true
+
+  - platform: gpio
+    name: "a8-output3"
+    id: switch_output3
+    pin:
+      pcf8574: pcf8574_hub_out_1
+      number: 2
+      mode: OUTPUT
+      inverted: true
+
+  - platform: gpio
+    name: "a8-output4"
+    id: switch_output4
+    pin:
+      pcf8574: pcf8574_hub_out_1
+      number: 3
+      mode: OUTPUT
+      inverted: true
+
+  - platform: gpio
+    name: "a8-output5"
+    id: switch_output5
+    pin:
+      pcf8574: pcf8574_hub_out_1
+      number: 4
+      mode: OUTPUT
+      inverted: true
+
+  - platform: gpio
+    name: "a8-output6"
+    id: switch_output6
+    pin:
+      pcf8574: pcf8574_hub_out_1
+      number: 5
+      mode: OUTPUT
+      inverted: true
+
+  - platform: gpio
+    name: "a8-output7"
+    id: switch_output7
+    pin:
+      pcf8574: pcf8574_hub_out_1
+      number: 6
+      mode: OUTPUT
+      inverted: true
+
+  - platform: gpio
+    name: "a8-output8"
+    id: switch_output8
+    pin:
+      pcf8574: pcf8574_hub_out_1
+      number: 7
+      mode: OUTPUT
+      inverted: true
+
+binary_sensor:
+  - platform: remote_receiver
+    name: "remoter1"
+    rc_switch_raw:
+      protocol: 3
+      code: '000000111110110100001'
+    on_press:
+        - switch.turn_off: switch_output7
+        - switch.turn_on: switch_output6
+    filters:
+      - delayed_off: 20ms
+
+  - platform: remote_receiver
+    name: "remoter2"
+    rc_switch_raw:
+      protocol: 3
+      code: '000000111110110100010'
+
+    on_press:
+      - switch.turn_off: switch_output6
+      - switch.turn_on: switch_output7
+    filters:
+      - delayed_off: 20ms
+
+  - platform: gpio
+    name: "a8-input1"
+    pin:
+      pcf8574: pcf8574_hub_in_1
+      number: 0
+      mode: INPUT
+      inverted: true
+    on_press:
+      - switch.toggle: switch_output1
+    on_release: 
+      - switch.toggle: switch_output1      
+        
+  - platform: gpio
+    name: "a8-input2"
+    pin:
+      pcf8574: pcf8574_hub_in_1
+      number: 1
+      mode: INPUT
+      inverted: true
+    on_press:
+      - switch.toggle: switch_output2
+    on_release: 
+      - switch.toggle: switch_output2  
+
+  - platform: gpio
+    name: "a8-input3"
+    pin:
+      pcf8574: pcf8574_hub_in_1
+      number: 2
+      mode: INPUT
+      inverted: true
+    on_press:
+      - switch.toggle: switch_output3
+    on_release: 
+      - switch.toggle: switch_output3
+
+  - platform: gpio
+    name: "a8-input4"
+    pin:
+      pcf8574: pcf8574_hub_in_1
+      number: 3
+      mode: INPUT
+      inverted: true
+    on_press:
+      - switch.toggle: switch_output4
+    on_release: 
+      - switch.toggle: switch_output4
+
+  - platform: gpio
+    name: "a8-input5"
+    pin:
+      pcf8574: pcf8574_hub_in_1
+      number: 4
+      mode: INPUT
+      inverted: true
+    on_press:
+      - switch.toggle: switch_output5
+    on_release: 
+      - switch.toggle: switch_output5
+
+  - platform: gpio
+    name: "a8-input6"
+    pin:
+      pcf8574: pcf8574_hub_in_1
+      number: 5
+      mode: INPUT
+      inverted: true
+    on_press:
+      - switch.toggle: switch_output6
+    on_release: 
+      - switch.toggle: switch_output6
+
+  - platform: gpio
+    name: "a8-input7"
+    pin:
+      pcf8574: pcf8574_hub_in_1
+      number: 6
+      mode: INPUT
+      inverted: true
+    on_press:
+      - switch.toggle: switch_output7
+    on_release: 
+      - switch.toggle: switch_output7
+
+  - platform: gpio
+    name: "a8-input8"
+    pin:
+      pcf8574: pcf8574_hub_in_1
+      number: 7
+      mode: INPUT
+      inverted: true
+    on_press:
+      - switch.toggle: switch_output8
+    on_release: 
+      - switch.toggle: switch_output8
+
+  - platform: gpio
+    name: "a8-s3"
+    pin:
+      number: 32
+      inverted: true
+
+  - platform: gpio
+    name: "a8-s4"
+    pin:
+      number: 33
+      inverted: true
+
+
+one_wire:
+  - platform: gpio
+    pin: GPIO14
+    id: bus14
+  
+sensor:
+  - platform: ina219
+    address: 0x40
+    shunt_resistance: 0.1 ohm
+    current:
+      name: "INA219 Current"
+      unit_of_measurement: "A"
+    power:
+      name: "INA219 Power"
+      unit_of_measurement: "W"
+      filters:
+      - multiply: 10
+    bus_voltage:
+      name: "INA219 Bus Voltage"
+      unit_of_measurement: "V"
+    shunt_voltage:
+      name: "INA219 Shunt Voltage"
+      unit_of_measurement: "V"
+    max_voltage: 32.0V
+    max_current: 3.2A
+    update_interval: 1s
+
+  - platform: dallas_temp
+    one_wire_id: bus14
+    name: "DS18B20"
+    update_interval: 2s
+    on_value_range: 
+      - above: 27.0
+        then:
+          - delay: 10s
+          - switch.turn_on: switch_output8
+      - below: 26.5
+        then:
+          - delay: 10s
+          - switch.turn_off: switch_output8
+    
+
+# web_server:
+#   port: 80
+#   auth:
+#     username: "silver"
+#     password: "cbvgcjy0"
+
+
+mqtt:
+  broker: 192.168.88.4
+  username: 'miroca'
+  password: 'cbvgcjy0'
+  discovery: False # disable entity discovery
+  discover_ip: True # enable device discovery

esp32-c3.yaml

@@ -22,10 +22,10 @@ ota:
 wifi:
   ssid: 'SmartHome'
   password: ''
-  use_address: 192.168.88.29
+  use_address: 192.168.88.#
 
   manual_ip:
-    static_ip: 192.168.88.29
+    static_ip: 192.168.88.#
     gateway: 192.168.88.1
     subnet: 255.255.255.0
   power_save_mode: none

gas-kocheg-wemos.yaml

@@ -47,12 +47,16 @@ sensor:
     icon: "mdi:meter-gas-outline"
 
 
-mqtt:
-  broker: 192.168.88.4
-  username: 'miroca'
-  password: 'cbvgcjy0'
-  discovery: False # disable entity discovery
-  discover_ip: True # enable device discovery
+# mqtt:
+#   broker: 192.168.88.4
+#   username: 'miroca'
+#   password: 'cbvgcjy0'
+#   discovery: False # disable entity discovery
+#   discover_ip: True # enable device discovery
 
 # web_server:
-#   port: 80
+#   port: 80
+#   auth:
+#     username: "silver"
+#     password: "cbvgcjy0"
+#   js_url: "http://192.168.88.4/static/file/upanel/js/esphome.js"

gas-podval-wemos.yaml

@@ -72,10 +72,11 @@ sensor:
 #   auth:
 #     username: "silver"
 #     password: "cbvgcjy0"
+#   js_url: "http://192.168.88.4/static/file/upanel/js/esphome.js"
 
-mqtt:
-  broker: 192.168.88.4
-  username: 'miroca'
-  password: 'cbvgcjy0'
-  discovery: False # disable entity discovery
-  discover_ip: True # enable device discovery
+# mqtt:
+#   broker: 192.168.88.4
+#   username: 'miroca'
+#   password: 'cbvgcjy0'
+#   discovery: False # disable entity discovery
+#   discover_ip: True # enable device discovery

generator.yaml

@@ -213,11 +213,12 @@ sensor:
     update_interval: 10s
     
 
-web_server:
-  port: 80
-  auth:
-    username: "silver"
-    password: "cbvgcjy0"
+# web_server:
+#   port: 80
+#   auth:
+#     username: "silver"
+#     password: "cbvgcjy0"
+#   js_url: "http://192.168.88.4/static/file/upanel/js/esphome.js"
 
 
 # mqtt:

kc868-a6.yaml

@@ -257,15 +257,16 @@ sensor:
       - multiply: 0.1
 
 
-web_server:
-  port: 80
-  auth:
-    username: "silver"
-    password: "cbvgcjy0"
+# web_server:
+#   port: 80
+#   auth:
+#     username: "silver"
+#     password: "cbvgcjy0"
+#   js_url: "http://192.168.88.4/static/file/upanel/js/esphome.js"
 
-mqtt:
-  broker: 192.168.88.4
-  username: 'miroca'
-  password: 'cbvgcjy0'
-  discovery: False # disable entity discovery
-  discover_ip: True # enable device discovery
+# mqtt:
+#   broker: 192.168.88.4
+#   username: 'miroca'
+#   password: 'cbvgcjy0'
+#   discovery: False # disable entity discovery
+#   discover_ip: True # enable device discovery

kontroller-kocheg-a16.yaml

@@ -511,10 +511,12 @@ sensor:
 #   auth:
 #     username: "silver"
 #     password: "cbvgcjy0"
+#   js_url: "http://192.168.88.4/static/file/upanel/js/esphome.js"
+  
 
-mqtt:
-  broker: 192.168.88.4
-  username: 'miroca'
-  password: 'cbvgcjy0'
-  discovery: False # disable entity discovery
-  discover_ip: True # enable device discovery
+# mqtt:
+#   broker: 192.168.88.4
+#   username: 'miroca'
+#   password: 'cbvgcjy0'
+#   discovery: False # disable entity discovery
+#   discover_ip: True # enable device discovery

kontroller-kocheg-a8.yaml

@@ -275,15 +275,16 @@ sensor:
     name: "DS18B20_server"
     update_interval: 10s
 
-web_server:
-  port: 80
-  auth:
-    username: "silver"
-    password: "cbvgcjy0"
+# web_server:
+#   port: 80
+#   auth:
+#     username: "silver"
+#     password: "cbvgcjy0"
+#   js_url: "http://192.168.88.4/static/file/upanel/js/esphome.js"
 
-mqtt:
-  broker: 192.168.88.4
-  username: 'miroca'
-  password: 'cbvgcjy0'
-  discovery: False # disable entity discovery
-  discover_ip: True # enable device discovery
+# mqtt:
+#   broker: 192.168.88.4
+#   username: 'miroca'
+#   password: 'cbvgcjy0'
+#   discovery: False # disable entity discovery
+#   discover_ip: True # enable device discovery

node.yaml

@@ -102,8 +102,9 @@ text_sensor:
     id: uptime_human
     icon: mdi:clock-start
 
-web_server:
-  port: 80
-  auth:
-    username: "silver"
-    password: "cbvgcjy0"
+# web_server:
+#   port: 80
+#   auth:
+#     username: "silver"
+#     password: "cbvgcjy0"
+#   js_url: "http://192.168.88.4/static/file/upanel/js/esphome.js"

test-wemos.yaml

@@ -0,0 +1,59 @@
+substitutions:
+  # Modify variables based on your settings
+  hostname: "test-wemos"
+  devicename: test-wemos
+
+esphome:
+  name: test-wemos
+  friendly_name: test_wemos
+
+esp8266:
+  board: esp01_1m
+
+# Enable logging
+logger:
+
+# Enable Home Assistant API
+api:
+  encryption:
+    key: "qEOA6hQaiz2eGOGyScJtwC7gGa1XyJEjw3qDShi529U="
+
+ota:
+  - platform: esphome
+    password: "95d41c6e935db2827ae63c2afeafec40"
+
+wifi:
+  ssid: 'SmartHome'
+  password: ''
+  use_address: 192.168.88.29
+
+  manual_ip:
+    static_ip: 192.168.88.29
+    gateway: 192.168.88.1
+    subnet: 255.255.255.0
+  power_save_mode: none
+
+
+
+
+captive_portal:
+
+sensor:
+
+switch:
+  - platform: gpio
+    name: switch
+    id: switch_output1
+    pin: GPIO4
+    inverted: True
+    restore_mode: ALWAYS_OFF
+    
+  - platform: restart
+    name: ${devicename} restart
+  
+# web_server:
+#   port: 80
+#   auth:
+#     username: "silver"
+#     password: "cbvgcjy0"
+#   js_url: "http://192.168.88.4/static/file/upanel/js/esphome.js"